Read PDF Hypertufa: How To Make Containers For You And Your Garden

Free download. Book file PDF easily for everyone and every device. You can download and read online Hypertufa: How To Make Containers For You And Your Garden file PDF Book only if you are registered here. And also you can download or read online all Book PDF file that related with Hypertufa: How To Make Containers For You And Your Garden book. Happy reading Hypertufa: How To Make Containers For You And Your Garden Bookeveryone. Download file Free Book PDF Hypertufa: How To Make Containers For You And Your Garden at Complete PDF Library. This Book have some digital formats such us :paperbook, ebook, kindle, epub, fb2 and another formats. Here is The CompletePDF Book Library. It's free to register here to get Book file PDF Hypertufa: How To Make Containers For You And Your Garden Pocket Guide.

Press the mixture against the sides of the form , leaving a thick wall with an opening for a plant. Make the walls inches 2.

Dallas Arboretum and Botanical Garden Blog

You will be able to see the shape of the finished plant pot as you complete it. Add a hole in the bottom for drainage. You can use your finger to form the hole. Allow the planter to dry thoroughly for about 7 days. Is this preparation waterproof or resistant to rain, snow etc.

It will withstand rain, ice and snow but it is best to keep it off the ground in freezing areas. Unless it is sealed which needs to be redone every few years , water will seep out of it slowly which is good for plants that don't like wet roots. You will need to water plants in unsealed pots more frequently than those in sealed pots. Yes No. Not Helpful 0 Helpful 7. It is not Hypertufa without using peat moss, preferably sphagnum peat moss.

Not Helpful 0 Helpful 2. Is it essential to soak the planter in water before planting to get rid of the lime? The water soak helps to cure it as well as to dilute the lime. Add vinegar to the water for a week before you plant anything in it. Not Helpful 3 Helpful 5.

Not Helpful 3 Helpful 2. Include your email address to get a message when this question is answered.

DIY Hypertufa Planters

Already answered Not a question Bad question Other. Tips You can embed materials, such as leaves, in the sides to create imprints. Or, texture the material with a wire brush. Hypertufa is quite alkaline and may cause the soil you place in it to become alkaline, also. Choose plants that prefer alkaline soil. Use Portland cement, not ready-mix concrete.

Try this using this material to make stepping stones and other garden statuary, too. Please be aware of the possible environmental consequences [1] of using peat moss. See the tips section for more information. You can mix the dry ingredients and store the mix, wetting only as much of it at a time as you need for one project.

Warnings Wear gloves when handling Portland cement and avoid skin contact. If your skin does contact this mixture, rinse well.

Avoid breathing the dry mixture or getting it in eyes. Hypertufa is very alkaline and can damage your plants unless you 'cure' it. Leave your pot outside exposed to the elements until the next planting season and the pot will be safe to use. If you are particularly ecologically-minded, you may wish to consider the possible ecological consequences [5] of using peat moss. Things You'll Need 3 parts peat moss.


  • Helpful Advice And Killer Combos For Your Hypertufa Containers | Hometalk.
  • Die Medlevinger - Phantastische Kinder- und Jugendliteratur im Unterricht (German Edition).
  • I filosofi di Hitler (Italian Edition);
  • Sieben Legenden (German Edition).

Related wikiHows. Did this article help you? This helps in the removal of the finished container. I found Portland cement at The Home Depot. The bag is heavy so take someone with you to load it if possible. One bag will be enough to make many projects, so don't be too concerned about the size of bag that it comes in.

Building the Form

Perlite and peat moss can be found at any hardware store or garden centre. Using a large container, measure out equal parts of the ingredients, estimating how much mixture you need for the size of your container. Add water slowly as you're looking for a certain consistency in the mixture. The goal is to be able to squeeze the mixture so it holds together easily and just a touch of water will drip out.

I wore gloves and mixed the Portland mixture with my hands. You can also use a tool of your choice from a garden trowel to shovel, depending on the size of your project. Test the consistency as you go to avoid adding too much water. If you happen to have too much water in your mix, add some Portland cement to tighten it up add a handful at a time, mix it in, then test. Once you have good consistency allow the mixture to sit for a few minutes while you assemble your mould. Starting at the bottom of your prepared container, begin to pack the mix into the mould, being sure to make the drainage holes.

Next, pat the mixture up the walls of the container. You can leave the centre hollow, shaping it with your hands or you can place a smaller container inside the first container to create the middle. If you do use a second container be sure to oil the surface well before inserting it.

I used a container to form the center of my pot. It was sitting a touch unlevel so I weighed it down with a few heavy stones. Walls should be a minimum of one inch thick.

What is a Hypertufa Pot?

The mould shape had a lot to do with the thickness of the walls of my planter. The steepness made the concrete really want to slide down. A container with less of a slope would be preferred if you're looking to create thinner walls. Keep that in mind when selecting your mould. When you're happy with the thickness of the walls, you need to place the hypertufa pot someplace to dry and cure.

The goal is a slow cure, so I recommend placing the containers into a large garbage bag. This holds in the moisture for a nice slow dry. Let it set for 24 to 36 hours.

How to Make a Hypertufa Planter

You can test it for dryness after 24 hours. Try to scratch it with your nail; if you can make a mark it's not fully dry. Give it another 12 to 24 hours. When you don't make a mark with the scratch test it's ready to unmould. If it's being stubborn, you can use a rubber mallet to tap the outer container to release the hypertufa pot. If you want to give the surface a bit of texture, you can use a wire brush to scratch it. Have fun with it! Next up is our cheater container. The finished product is similar to rough stone and we can play with colour a bit in this project.

For the faux stone planter you need:. Once I started shopping for Styrofoam containers I was able to find them everywhere, from grocery stores to my local hardware store.

Easy DIY Hypertufa Projects | The Garden Glove

I went with a smaller cooler for my first project but have since picked up a larger one for my next faux stone planter. I bought a small can of exterior latex paint in a medium grey. The goal is to make it look like stone, so keep that colour palette in mind when shopping for paint. I used a one-inch paint brush. Don't spend too much money on the brush as it gets quite gritty and you'll only want to use it for outdoor projects.

The sand can also be found at the hardware store or in some garden centres. You need to do this project outside as it's messy! Cover your table with a sheet of plastic to protect it from paint drips. Using a sharp knife cut drain holes into the bottom of your cooler.


  • Navigation Menu: Social Icons;
  • 5 gute Gründe, die eigene Grabrede zu entwerfen (German Edition).
  • How To Make Hypertufa Planters - House of Hawthornes;
  • How to Make Hypertufa Planters: 8 Steps (with Pictures) - wikiHow?
  • How To Make Hypertufa Planters.
  • | Better Homes & Gardens.
  • Is Home Really the Best Place? (A Laugh-Out-Loud Family Comedy)!

Now we get to have some fun!